Craft supply tray

Keep cutting tools apart from capped adhesives and return them as the craft session changes stages. All files are free, including your customized plan.

Fixed divider

Keep cutting tools apart from capped adhesives and return them as the craft session changes stages.

One fixed partition keeps a covered cutting tool from landing against adhesive containers while leaving the full tool length accessible.

For Someone making small paper or fabric crafts at a desk. Default clear opening: 191.5 mm × 227 mm × 51 mm.

Adjust dimensions and stock ↓

Measure before you start

Measure closed scissors with their protective cover fitted.
Measure the glue-stick or tape-dispenser group at its widest point.

Tools and access

A saw and guide for straight cuts
A square, measuring rule and caliper
Clamps suitable for the dry assembly
A sanding block for accessible edges

Using this organizer

Place covered cutting tools in one lane and capped adhesives in the other.
Take a tool to the work surface for each operation.
Clean, close and cover it before returning it.

What a useful result needs to do

Covered scissors lie flat with neither handle nor tip bridging a divider.
An adhesive can be lifted without reaching across exposed tool edges.
Both groups can be cleared separately when cleaning the tray.

If the fit is wrong

If the protective cover changes the fit, resize using the covered tool measurement.
If adhesive residue makes retrieval sticky, remove the affected items and clean them before returning.

.config,#download button,#compare-stock,.step-check{display:none}.workspace{display:block}Turn on JavaScript to adjust dimensions. You can still download and print the original complete plan.Download original complete ZIP Open original print plan

Ready to make. All 6 parts fit the listed stock.

Your parts

Cut length	Cut width	Thickness	Qty	Grain
410 mm	60 mm	9 mm	2	Along length
227 mm	60 mm	9 mm	2	Along length
392 mm	227 mm	9 mm	1	Unrestricted
227 mm	51 mm	9 mm	1	Along length

Item allowance: craft tools — 180 × 80 mm, plus 10 mm of handling space per axis.

A feasible cutting layout

Numbered cuts span their parent region. Coordinates use the sheet's top-left origin. Trim all four edges of each sheet you use first. Keep unused sheets whole. This layout does not claim the lowest possible material use.

Compare your stock choices

Try this same inventory with offcuts first and standard sheets first. Each result is a feasible estimate; the solver may miss a better layout.

Sheet S1.1

Cut sequence

Cut	Parent region	Direction	Coordinate (mm)	First child	Second child
C1	N1	horizontal	65	N2	N3
C2	N2	vertical	415	N4	N5
C3	N3	horizontal	128	N6	N7
C4	N6	vertical	415	N8	N9
C5	N7	horizontal	358	N10	N11
C6	N10	vertical	397	N12	N13
C7	N11	horizontal	421	N14	N15
C8	N14	vertical	232	N16	N17
C9	N17	vertical	462	N18	N19
C10	N15	horizontal	475	N20	N21
C11	N20	vertical	232	N22	N23

Connections and machining

Fixed dividers · 6 pieces · 9 mm plywood. Fixed dividers stand on the inset base and meet the front and back walls. Glue the divider bottoms and ends after the outer shell is square.

No grooves or notches are required. Cut the rectangular parts, then follow the connection details.

Put it together

Done
1. Measure and mark
Measure the actual sheet thickness (9 mm in this plan). Mark front / back F, left / right L, base P and dividers D. Recalculate if the measured thickness differs. Measure closed scissors end to end and keep any protective covers.
Parts: F, L, P, D · Start here
Done
2. Cut and label the parts
Follow the numbered full-width cuts in the cutting sequence, then subdivide each labeled child region. Keep the part IDs and grain arrows. Use the instructions supplied with your tools; this plan is not tool training.
Parts: F, L, P, D · After measure
Done
3. Dry-fit the outer walls
Front and back span 410 mm. Fit the 227 mm side walls between them. Check the outside footprint 410 × 245 mm and square the corners. The inset base is 392 × 227 mm; its underside sits flush with the wall bottoms. Total base clearance is 0 mm per axis (0 mm on each side).
Parts: F, L, P · After cut
Done
4. Assemble the base and walls
Prepare and bond the butt-joint contact faces using an adhesive suitable for your sheet. Center the inset base at z = 0 mm. Check squareness before clamping. For a clearance gap, verify the adhesive allows that gap; use zero clearance or revise the fit if it does not.
Parts: F, L, P · After dry-fit
Done
5. Position the dividers
Mark each divider from the inside face of the left wall. Place the first divider after 191.50 mm of clear space; repeat at a pitch of 200.50 mm. Glue the bottom edge onto P and both ends against F. Each compartment has 191.50 × 227 mm clear floor space. These are straight glued partitions, with no grooves or hidden fasteners.
Parts: D, F, P · After glue
Done
6. Cure, finish and check the fit
Follow the adhesive manufacturer's cure and handling instructions. Smooth edges and apply a finish compatible with your materials. Attach four self-adhesive felt pads under the base corners. Store capped adhesive and covered blades; no child-safety certification is claimed. Use for light desktop items; no load rating is provided.
Parts: F, L, P, D · After divide

Materials and supplies

Uses 1 standard sheet(s) and 0 existing offcut(s). Check your inventory before buying.
S1: 1 of 1 used · 600 × 600 × 9 mm plywood (standard sheet).
Four self-adhesive felt pads.
Adhesive suitable for the selected sheet. Prepare according to the adhesive label and actual contact faces; no universal quantity or cure time.
Compatible finish and abrasive. Choose for the actual material and intended indoor use.

Take the complete plan

Parts, stock, cutting sequence and machining CSVs, connection and assembly diagrams, a printable plan and editable JSON. No sign-up.

For PDF, open the print page and choose Save as PDF in your browser. Use A4 or Letter.

For light desktop storage. Geometry checked; physical assembly and durability untested. Follow your tool, sheet and adhesive instructions. Adhesive quantity and curing time depend on the product you use.

More for craft & small parts

Fixed divider

Paint jar organizer

8 parts·9 mm plywood

Keep paint jars in separate color groups and remove a closed jar before opening it for use.

Clear opening 63.75 mm × 162 mm × 56 mm

Removable divider

Sewing notion divider

7 parts·12 mm plywood

Separate closures, marking tools and small notion boxes, then open a wider lane for the current kit.

Clear opening 104 mm × 226 mm × 78 mm