Skip to content
Small Shop Plans
Project library / Everyday

Small drawer insert

Separate small drawer contents while keeping the entire insert easy to remove for cleaning. All files are free, including your customized plan.

Fixed divider

Separate small drawer contents while keeping the entire insert easy to remove for cleaning.

A separate low tray can lift out as one piece. Its outer dimensions must pass through the drawer opening as well as fit the interior.

For Someone fitting a removable organizer into an existing desk drawer. Default clear opening: 112 mm × 248 mm × 49 mm.

Adjust dimensions and stock ↓
Measure before you start
  • Measure the narrowest drawer opening, clear interior width and depth, and closed-drawer height.
  • Allow at least 4 mm around the insert and check handles or runners that intrude during removal.
Tools and access
  • A saw and guide for straight cuts
  • A square, measuring rule and caliper
  • Clamps suitable for the dry assembly
  • A sanding block for accessible edges
Using this organizer
  1. Test an outer-size cardboard footprint through the drawer opening.
  2. Place the finished insert inside and assign one group to each lane.
  3. Close the loaded drawer gently, then remove the whole insert for cleaning when needed.
What a useful result needs to do
  • The loaded drawer closes through its full travel without contact.
  • The insert can be lifted out through the opening with a hand grip.
  • Objects stay below the drawer's moving obstructions.
If the fit is wrong
  • If the opening is narrower than the interior, size to the opening rather than the drawer base.
  • If an object catches during closing, remove it and reduce its stored height before using the drawer.
Ready to make. All 7 parts fit the listed stock.
Small drawer insert — thumbnail assemblyDimensions are in millimeters. Read the stated measurements; this drawing is not a full-size cutting template.Fixed dividers · Assembled view360 × 260 × 55 mm · thickness 6 mm

Your parts

PartCut lengthCut widthThicknessQtyGrain
360 mm55 mm6 mm2Along length
248 mm55 mm6 mm2Along length
348 mm248 mm6 mm1Unrestricted
248 mm49 mm6 mm2Along length
Small drawer insert — dimensionsDimensions are in millimeters. Read the stated measurements; this drawing is not a full-size cutting template.Overall dimensions and clear openingsTop view · front edge at the bottomP1360 mm260Front section · halfway through depth (130 mm)F1F2360 mm55Clear width 112 · depth 248 mmClear height 49 · plywood 6 mmRead each opening and part from the plan before cutting.

Item allowance: drawer items — 95 × 80 mm, plus 8 mm of handling space per axis.

A feasible cutting layout

Numbered cuts span their parent region. Coordinates use the sheet's top-left origin. Trim all four edges of each sheet you use first. Keep unused sheets whole. This layout does not claim the lowest possible material use.

Compare your stock choices

Try this same inventory with offcuts first and standard sheets first. Each result is a feasible estimate; the solver may miss a better layout.

Sheet S1.1

Feasible cutting layout S1.1S1.1 · 600 × 600 × 6 mmC1C2C3C4C5C6C7C8C9C10C11C12F1360 × 55F2360 × 55P1348 × 248L1248 × 55L2248 × 55D1248 × 49D2248 × 49Hatched bands: 3 mm kerf · trim 5 mm on every edgeGrain arrows · small-part locations: @ x,y mm from sheet top-left
Cut sequence
CutParent regionDirectionCoordinate (mm)First childSecond child
C1N1horizontal60N2N3
C2N2vertical365N4N5
C3N3horizontal118N6N7
C4N6vertical365N8N9
C5N7horizontal369N10N11
C6N10vertical353N12N13
C7N11horizontal427N14N15
C8N14vertical253N16N17
C9N17vertical504N18N19
C10N15horizontal479N20N21
C11N20vertical253N22N23
C12N23vertical504N24N25

Connections and machining

Fixed dividers · 7 pieces · 6 mm plywood. Fixed dividers stand on the inset base and meet the front and back walls. Glue the divider bottoms and ends after the outer shell is square.
Small drawer insert — connectionsDimensions are in millimeters. Read the stated measurements; this drawing is not a full-size cutting template.Fixed dividers · connection detailsBase and divider contact · front section at mid-depthF1F2360 mm55Bond the divider bottoms to the base and the ends to the frontand back walls. Space each opening before the glue sets.Joint reference spans · length × width (mm)F + L · 6 × 55F + P · 348 × 6D + P · 248 × 6
Small drawer insert — machiningDimensions are in millimeters. Read the stated measurements; this drawing is not a full-size cutting template.Rectangular blanks · no grooves or notchesFixed dividers · 7 pieces · 6 mm plywood. Fixed dividers stand onthe inset base and meet the front and back walls. Glue thedivider bottoms and ends after the outer shell is square.Follow the cutting map, then use the connection details forassembly.

No grooves or notches are required. Cut the rectangular parts, then follow the connection details.

Put it together

Small drawer insert — exploded assemblyDimensions are in millimeters. Read the stated measurements; this drawing is not a full-size cutting template.Fixed dividers · Exploded assemblyF1F2L1L2P1D1D2360 × 260 × 55 mm · thickness 6 mmFixed dividers stand on the inset base and meet the front and backwalls. Glue the divider bottoms and ends after the outer shell issquare.Part labels match the cutting list. Use numerical dimensions.

  1. 1. Measure and mark

    Measure the actual sheet thickness (6 mm in this plan). Mark front / back F, left / right L, base P and dividers D. Recalculate if the measured thickness differs. Measure the drawer opening and usable interior, allowing at least 4 mm around this insert.

    Parts: F, L, P, D · Start here

  2. 2. Cut and label the parts

    Follow the numbered full-width cuts in the cutting sequence, then subdivide each labeled child region. Keep the part IDs and grain arrows. Use the instructions supplied with your tools; this plan is not tool training.

    Parts: F, L, P, D · After measure

  3. 3. Dry-fit the outer walls

    Front and back span 360 mm. Fit the 248 mm side walls between them. Check the outside footprint 360 × 260 mm and square the corners. The inset base is 348 × 248 mm; its underside sits flush with the wall bottoms. Total base clearance is 0 mm per axis (0 mm on each side).

    Parts: F, L, P · After cut

  4. 4. Assemble the base and walls

    Prepare and bond the butt-joint contact faces using an adhesive suitable for your sheet. Center the inset base at z = 0 mm. Check squareness before clamping. For a clearance gap, verify the adhesive allows that gap; use zero clearance or revise the fit if it does not.

    Parts: F, L, P · After dry-fit

  5. 5. Position the dividers

    Mark each divider from the inside face of the left wall. Place the first divider after 112.00 mm of clear space; repeat at a pitch of 118.00 mm. Glue the bottom edge onto P and both ends against F. Each compartment has 112.00 × 248 mm clear floor space. These are straight glued partitions, with no grooves or hidden fasteners.

    Parts: D, F, P · After glue

  6. 6. Cure, finish and check the fit

    Follow the adhesive manufacturer's cure and handling instructions. Smooth edges and apply a finish compatible with your materials. Attach four self-adhesive felt pads under the base corners. Dry-fit in the drawer before finishing. Check that the drawer closes freely. Use for light desktop items; no load rating is provided.

    Parts: F, L, P, D · After divide

Materials and supplies

  • Uses 1 standard sheet(s) and 0 existing offcut(s). Check your inventory before buying.
  • S1: 1 of 1 used · 600 × 600 × 6 mm plywood (standard sheet).
  • Four self-adhesive felt pads.
  • Adhesive suitable for the selected sheet. Prepare according to the adhesive label and actual contact faces; no universal quantity or cure time.
  • Compatible finish and abrasive. Choose for the actual material and intended indoor use.

Take the complete plan

Parts, stock, cutting sequence and machining CSVs, connection and assembly diagrams, a printable plan and editable JSON. No sign-up.

For PDF, open the print page and choose Save as PDF in your browser. Use A4 or Letter.

For light desktop storage. Geometry checked; physical assembly and durability untested. Follow your tool, sheet and adhesive instructions. Adhesive quantity and curing time depend on the product you use.

More for everyday

Open desktop tray — thumbnail assemblyDimensions are in millimeters. Read the stated measurements; this drawing is not a full-size cutting template.Open tray · Assembled view400 × 250 × 100 mm · thickness 12 mm
Open tray

Open desktop tray

5 parts·12 mm plywood

Collect the things that otherwise remain scattered, then return the whole desk to use.

Clear opening 376 mm × 226 mm × 88 mm
Two-compartment stationery tray — thumbnail assemblyDimensions are in millimeters. Read the stated measurements; this drawing is not a full-size cutting template.Fixed dividers · Assembled view380 × 220 × 65 mm · thickness 9 mm
Fixed divider

Two-compartment stationery tray

6 parts·9 mm plywood

Keep writing tools separate from clips and erasers so a pen can be taken without disturbing small pieces.

Clear opening 176.5 mm × 202 mm × 56 mm