Tablet resting divider

Park an inactive tablet in its existing sleeve beside its disconnected accessories. All files are free, including your customized plan.

Fixed divider

Park an inactive tablet in its existing sleeve beside its disconnected accessories.

Two broad lanes keep the sleeve apart from accessories. The design supplies storage space; the sleeve supplies the device's existing surface protection.

For Someone putting away a sleeved tablet between desk sessions. Default clear opening: 122 mm × 261 mm × 128 mm.

Adjust dimensions and stock ↓

Measure before you start

Measure the closed sleeve including seams, zip pulls and any cover flap.
Check the upright height and the space needed to grip the sleeve above the box.

Tools and access

A saw and guide for straight cuts
A square, measuring rule and caliper
Clamps suitable for the dry assembly
A sanding block for accessible edges

Using this organizer

Disconnect the device and close its sleeve before storage.
Place the sleeve in one lane and its loose accessories in the other.
Lift the sleeve with a hand on the device rather than pulling a cable.

What a useful result needs to do

The complete sleeve enters without being squeezed.
The device remains reachable by its sleeve edges.
Accessory plugs stay separate from the screen-facing sleeve surface.

If the fit is wrong

If the loaded organizer feels unsteady, store the device flat in a suitable open cubby.
If a zip pull catches, enlarge the measured envelope and recalculate.

.config,#download button,#compare-stock,.step-check{display:none}.workspace{display:block}Turn on JavaScript to adjust dimensions. You can still download and print the original complete plan.Download original complete ZIP Open original print plan

Ready to make. All 6 parts fit the listed stock.

Your parts

Cut length	Cut width	Thickness	Qty	Grain
280 mm	140 mm	12 mm	2	Along length
261 mm	140 mm	12 mm	2	Along length
256 mm	261 mm	12 mm	1	Unrestricted
261 mm	128 mm	12 mm	1	Along length

Item allowance: tablet sleeve and accessories (floor footprint) — 70 × 245 mm, plus 8 mm of handling space per axis.

A feasible cutting layout

Numbered cuts span their parent region. Coordinates use the sheet's top-left origin. Trim all four edges of each sheet you use first. Keep unused sheets whole. This layout does not claim the lowest possible material use.

Compare your stock choices

Try this same inventory with offcuts first and standard sheets first. Each result is a feasible estimate; the solver may miss a better layout.

Sheet S1.1

Cut sequence

Cut	Parent region	Direction	Coordinate (mm)	First child	Second child
C1	N1	horizontal	145	N3	N4
C2	N3	vertical	285	N5	N6
C3	N6	vertical	568	N7	N8
C4	N4	horizontal	409	N9	N10
C5	N9	vertical	261	N11	N12
C6	N8	vertical	832	N13	N14
C7	N10	horizontal	552	N15	N16
C8	N15	vertical	266	N17	N18
C9	N18	horizontal	540	N19	N20
C10	N19	vertical	530	N21	N22

Sheet S1.2

Cut sequence

Cut	Parent region	Direction	Coordinate (mm)	First child	Second child

Connections and machining

Fixed dividers · 6 pieces · 12 mm plywood. Fixed dividers stand on the inset base and meet the front and back walls. Glue the divider bottoms and ends after the outer shell is square.

No grooves or notches are required. Cut the rectangular parts, then follow the connection details.

Put it together

Done
1. Measure and mark
Measure the actual sheet thickness (12 mm in this plan). Mark front / back F, left / right L, base P and dividers D. Recalculate if the measured thickness differs. Measure the actual sleeve; this plan checks storage space only.
Parts: F, L, P, D · Start here
Done
2. Cut and label the parts
Follow the numbered full-width cuts in the cutting sequence, then subdivide each labeled child region. Keep the part IDs and grain arrows. Use the instructions supplied with your tools; this plan is not tool training.
Parts: F, L, P, D · After measure
Done
3. Dry-fit the outer walls
Front and back span 280 mm. Fit the 261 mm side walls between them. Check the outside footprint 280 × 285 mm and square the corners. The inset base is 256 × 261 mm; its underside sits flush with the wall bottoms. Total base clearance is 0 mm per axis (0 mm on each side).
Parts: F, L, P · After cut
Done
4. Assemble the base and walls
Prepare and bond the butt-joint contact faces using an adhesive suitable for your sheet. Center the inset base at z = 0 mm. Check squareness before clamping. For a clearance gap, verify the adhesive allows that gap; use zero clearance or revise the fit if it does not.
Parts: F, L, P · After dry-fit
Done
5. Position the dividers
Mark each divider from the inside face of the left wall. Place the first divider after 122.00 mm of clear space; repeat at a pitch of 134.00 mm. Glue the bottom edge onto P and both ends against F. Each compartment has 122.00 × 261 mm clear floor space. These are straight glued partitions, with no grooves or hidden fasteners.
Parts: D, F, P · After glue
Done
6. Cure, finish and check the fit
Follow the adhesive manufacturer's cure and handling instructions. Smooth edges and apply a finish compatible with your materials. Attach four self-adhesive felt pads under the base corners. Use an intact padded sleeve. This is not a device protection or load-rated stand. Use for light desktop items; no load rating is provided.
Parts: F, L, P, D · After divide

Materials and supplies

Uses 1 standard sheet(s) and 0 existing offcut(s). Check your inventory before buying.
S1: 1 of 2 used · 900 × 600 × 12 mm plywood (standard sheet). Unused stock stays whole.
Four self-adhesive felt pads.
Adhesive suitable for the selected sheet. Prepare according to the adhesive label and actual contact faces; no universal quantity or cure time.
Compatible finish and abrasive. Choose for the actual material and intended indoor use.

Take the complete plan

Parts, stock, cutting sequence and machining CSVs, connection and assembly diagrams, a printable plan and editable JSON. No sign-up.

For PDF, open the print page and choose Save as PDF in your browser. Use A4 or Letter.

For light desktop storage. Geometry checked; physical assembly and durability untested. Follow your tool, sheet and adhesive instructions. Adhesive quantity and curing time depend on the product you use.

More for everyday

Open tray

Open desktop tray

5 parts·12 mm plywood

Collect the things that otherwise remain scattered, then return the whole desk to use.

Clear opening 376 mm × 226 mm × 88 mm

Removable divider

Mail and device divider

7 parts·12 mm plywood

Separate active mail from an inactive device, then remove a partition when a wider folder temporarily needs the space.

Clear opening 124 mm × 261 mm × 113 mm